- Categories
- Home and Garden
- Tools
Download Article
Explore this Article
methods
1Reading a Micrometer Torque Wrench
2Understanding the Numbers on a Beam or Dial Torque Wrench
3Using a Digital-Read Torque Wrench
Other Sections
Video
Tips and Warnings
Related Articles
References
Co-authored byHovig Manouchekian
Last Updated: December 30, 2023References
Download Article
Knowing the level of torque you’re applying to a nut is essential for the stability of a piece of machinery or structure. If you use too little torque, the nut may not be secure, and if you apply too much, you could strip the threads along the bolt. Luckily, several types of wrenches will help you determine how much torque you’re applying. The most common types of these tools are micrometer, beam, dial, and digital torque wrenches. If you use your torque wrench correctly, it should be simple to read it.
Method 1
Method 1 of 3:
Reading a Micrometer Torque Wrench
Download Article
1
Rotate the knob on the end of the handle counter-clockwise. Turning the knob on the end of the handle will loosen the torque wrench and allow you to rotate it. Loosen the knob before you try to adjust the torque settings.[1]
2
Find the vertically listed numbers above the wrench handle. You should see 2 sets of vertical numbers on both sides of your torque wrench. One side of the wrench will be in foot-pounds or ft.-lbs., and the other set of numbers will be in Newton meters or Nm. These are both different units used to measure torque. The vertically listed numbers are usually called the main scale and represent the amount of torque your wrench is set to, to the nearest ten.[2]
- The numbers will have horizontal lines running next to them.
Advertisem*nt
3
Find the numbers wrapped around the wrench’s handle. The numbers that wrap around the wrench’s handle are usually referred to as the micrometer. These numbers measure the second number in your torque measurement and allow you to set a more precise torque level.[3]
4
Turn the handle on the wrench to adjust the torque setting. Turning the handle clockwise will increase the torque while turning it counterclockwise will reduce it. You’ll notice that as you rotate the handle on the wrench, the handle will move up and down while the numbers on the micrometer will rotate. Turning the handle will affect both the main scale and the micrometer scale at the same time.[4]
5
Set the wrench for the precise torque you're seeking. Line up the vertical line on the handle of your wrench with the vertical line above each number on the micrometer to reach your desired setting.[5]
- For example, if your main scale is slightly above the 90-ft.-lbs. (122 Nm) horizontal line and the 3 on the micrometer lines up with the vertical line, it means that your wrench is set to 93 feet (28.3m).-lbs. (126 Nm).
6
Tighten the knob at the end of the torque wrench. Turn the knob at the end of the wrench handle clockwise. This will tighten the wrench and set the level of torque on the wrench. If you need to adjust the torque again, loosen the knob and turn the handles to the torque that you need.[6]
- Be careful when tightening the bolt because you could lose the measurement if you drop the wrench.
7
Listen for the click while you work. As you use the wrench, you'll hear a click when you reach the set level of torque. So stop tightening when you hear that click![7]
- Store the wrench on the lowest torque setting so there isn’t tension on the mechanism.
Advertisem*nt
Method 2
Method 2 of 3:
Understanding the Numbers on a Beam or Dial Torque Wrench
Download Article
1
Look at the meter at the bottom of the torque wrench. There should be a meter at the bottom of the wrench with numbers and an arrow. The numbers represent the amount of torque in either foot-pounds (ft.-lbs.) or Newton meters (Nm). Wherever the arrow is pointed designates the amount of torque that you’re applying to a lug or nut. In the stationary position, the wrench should read 0.[8]
2
Turn the wrench around a nut or bolt and look at the arrow. As you turn the wrench around a nut or bolt, the arrow will move and represent the amount of torque you’re applying. For example, if you turn the wrench around the nut and it reads 30 lbs.-ft (40.7 Nm), that means you’re applying that level of torque to the nut. Apply force slowly to avoid damaging the bolt.[9]
- Read the arrow from directly above so you get an accurate reading.
- Some dial torque wrenches will have a memory arrow that follows the main arrow and stays at the highest level of torque. This makes it so that even if you disengage the wrench, you’ll know the max torque you were applying to the nut.
3
Put a piece of tape on your desired torque line to read it more easily. There are a lot of lines and numbers on a beam or dial torque wrench, so it may be hard to see it without the tape. If your wrench doesn’t have a memory arrow, you can put a piece of tape next to the line of the desired amount of torque. Putting tape near the line will make the wrench easier to read.[10]
Advertisem*nt
Method 3
Method 3 of 3:
Using a Digital-Read Torque Wrench
Download Article
1
Read the instruction manual that came with the wrench. The instruction manual will tell you how to adjust the torque settings on your wrench and will explain how to change the units of measure to read in either foot-pounds (ft.-lbs.) or Newton Meters (Nm).
- Clean the threads of the bolt you want to torque without any lubricant or tape.
- Some digital torque wrenches will also have other settings that affect the sounds and vibration levels.[11]
2
Use the arrow keys to set a designated amount of torque. Press the up or down arrow to change the torque setting on the wrench. Continue to modify the numbers until you hit your desired level of torque.[12]
3
Set the tolerance parameters with the% key. Some electronic torque wrenches will have tolerance parameters that will help you with precision. These parameters allow you to set a warning on your wrench before it reaches the desired torque. For example, if you set the tolerance parameters to 10%, the wrench will start lighting up and vibrating when you're within 10% of your desired torque. Set the tolerance parameters by hitting the% key, then using the arrow keys to change the percentage.[13]
- Use this setting if you need precise torque.
4
Stop turning the wrench when it lights up or makes a noise. When you reach the amount of torque you need, the wrench will make a sound, light up, or vibrate. Stop turning the nut when this happens.[14]
Advertisem*nt
Video
Tips
Adjust the torque if you use any offsets, extensions, or adapters. Use 1 ft-lb (1.36 Nm) per 1in (2.5cm) of extension.
Thanks
Helpful2Not Helpful0
If you’re tightening the bolts on your car’s tires, you can refer to the owner’s manual to see the torque that's required to tighten them. For other items, check product descriptions before you try to tighten a nut so that you know how much torque is required to tighten it.
Thanks
Helpful1Not Helpful0
Not tightening bolts or lugs enough could cause your equipment to fall apart and is unsafe.
Thanks
Helpful1Not Helpful0
Submit a Tip
All tip submissions are carefully reviewed before being published
Submit
Thanks for submitting a tip for review!
Advertisem*nt
You Might Also Like
Advertisem*nt
References
- ↑ https://manuals.harborfreight.com/manuals/61000-61999/61277.pdf
- ↑ https://www.tekton.com/manuals/manual_24330.pdf
- ↑ https://manuals.harborfreight.com/manuals/61000-61999/61277.pdf
- ↑ https://www.youtube.com/watch?v=AriiR1i0DmI&t=4m41s
- ↑ https://homesteady.com/how-4814062-read-torque-wrench.html
- ↑ https://manuals.harborfreight.com/manuals/61000-61999/61277.pdf
- ↑ https://homesteady.com/how-4814062-read-torque-wrench.html
- ↑ https://www.youtube.com/watch?v=Eo2sq9BIC_8&t=1m45s
- ↑ https://www.youtube.com/watch?v=Eo2sq9BIC_8&t=2m2s
More References (5)
About This Article
Co-authored by:
Hovig Manouchekian
Auto Repair & Design Specialist
This article was co-authored by Hovig Manouchekian. Hovig Manouchekian is an Auto Repair and Design Specialist and the Manager of Funk Brothers Auto, a family-owned business operated since 1925. With over 30 years of experience in the automotive industry, Hovig specializes in the process of auto repair and maintenance. He is also very knowledgeable in common automotive issues and needs including engine repair, battery replacement, and windshield accessory and maintenance. Hovig's knowledge and hard work have contributed to Funk Brothers Auto winning Angie's List Super Service Award for five consecutive years. This article has been viewed 155,692 times.
2 votes - 50%
Co-authors: 4
Updated: December 30, 2023
Views:155,692
Categories: Tools
In other languages
Spanish
French
- Send fan mail to authors
Thanks to all authors for creating a page that has been read 155,692 times.
Did this article help you?
Advertisem*nt